Power Amplifiers

Balanced Audio Technology VK-250, excellent condition Learn More

Mcintosh MC7270 One in excellent 8/22 One in service 6/22 awaiting new factory glass, main output filter caps will be changed out also. Original box from Mcintosh if shipped, inquire for freight cost Too fragile for Fedex or UPS ground. Learn More

Anthem P2 retail $4500 in very good condition Learn More

Krell KSA250 from original owner one left Learn More

Mark Levinson 332 picked up 1/22 from original owner Learn More

Devialet Expert 200, original box/packing, excellent condition Learn More

excellent condition Mark Levinson 23 200 watt/channel amplfiier, 100V set at present, can be changed Description: Solid-state stereo power amplifier. Rated power output: 200Wpc continuous into 8 ohms (23dBW) with less than 0.1% THD, 400Wpc continuous into 4 ohms (23dBW) with less than 0.2% THD, both from 20Hz–20kHz, both channels driven. Damping factor: greater than 600 at 50Hz, 8 ohms (equivalent to an output impedance of 0.013 ohms). Frequency response: 4Hz–140kHz, —dB. Input impedance: 50k ohms shunted by 1.5nF. Voltage gain: 26dB (load not defined). Input sensitivity: 141mV for 1W output. Dimensions: 19" (483mm) W by 8.25" (210mm) H by 15.7" (399mm) D. Shipping weight: 105 lbs (48kg). Learn More

Mcintosh MC2505 in beautiful condition, one owner in 3/23 New box and packing ordered from Mcintosh 3/23 optional wood case pictured $350 additional plus shipping Learn More

Krell FPB250M excellent like new cosmetics Recapped! factory boxes MULTIPLE AVAILABLE Power output: 250W into 8Ω (mono) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.03% Gain: 26.4 dB Input sensitivity: 2.14V Signal to noise ratio: 114dB Dimensions: 318 x 267 x 406mm Weight: 31kg Learn More

Crown Reference 1 in service 9/21 Inquire before purchasing Reference I (120 V, 60 Hz models) The Crown® Studio Reference I power amplifier shall be a solid-state two-channel model employing multi-mode (AB+B) grounded bridge(TM) output circuitry with a variable impedance (VZ) power supply for each channel. The outputs shall be switchable as stereo, bridged-mono or parallel-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. The parallel-mono mode shall parallel the outputs to provide increased output current. The output impedance of each channel shall be less than 10 milliohms in series with less than 2 microhenries in stereo mode. The variable impedance power supplies shall reduce unnecessary voltage across the output devices by automatically switching to a parallel mode when less voltage is required by the output circuitry and to a series mode when more voltage is required. The amplifier shall contain protection circuitry which limits the drive level placed on the output devices before their SOA (Safe Operating Area) is exceeded. This protection circuitry shall calculate the instantaneous voltage across and current through the output devices while factoring in their simulated junction temperatures to predict how close they are to their operating limits. This protection will be called “ODEP.” The amplifier shall contain controlled slew-rate voltage circuitry to protect it against radio frequency interference burnouts. It shall also be protected from current overload at its output stage. The slew rate of the amplifier shall be greater than 30 volts per microsecond in stereo mode. The amplifier shall temporarily go into a stand-by mode if its power transformer becomes excessively hot and shall automatically resume normal operation once it has cooled to a safe operating temperature. Front-panel controls shall include an enable on/off switch and a detented input level control for each channel. Rear-mounted controls shall include a ground lift switch to isolate the signal ground from the chassis ground, a switch which selects between stereo, bridged-mono and parallel-mono modes of operation and a reset switch for the AC mains circuit breaker. Internal controls shall include an input sensitivity switch to select between 0.775 V, 1.4 V or a fixed voltage gain of 26 dB for full rated output. A Crown P.I.P. and P.I.P.2-compatible expansion connector shall be provided behind an access panel in the rear to accept auxiliary input modules. It shall be fully compatible with the Crown IQ System. Front panel indicators shall include an amber power enable indicator, an amber ODEP protection system indicator for each channel which shall normally be illuminated to confirm the availability of reserve thermodynamic energy and which shall dim in proportion to limiting when the power demands of the output stages have been exceeded, a green IOC indicator for each channel, and a green Signal indicator for each channel which shall normally flash at moderate intensity to show the presence of an audio signal. The power amplifier shall meet or exceed the following performance criteria. Input sensitivity for rated output: 26 dB voltage gain (unbalanced). Rated FTC output in stereo mode with less than 0.1% THD: 780watts per channel (20 Hz to 20 kHz) into 8 ohms. Hum and noise: at least 120 dB (A weighted) below full rated output power. Phase response: +5 to –15 degrees from 20 Hz to 20 kHz at 1 watt. Frequency response: 20 Hz to 20 kHz, 0.1 dB at 1 watt into 8 ohms per channel in stereo mode. Damping factor: greater than 20,000 from 10 to 200 Hz into 8 ohms. Intermodulation distortion (SMPTE): less than 0.005% from full bandwidth power to 78 watts rising linearly to better than 70 dB at 20 kHz. Harmonic distortion: less than 0.02% at rated low-distortion 1 kHz power. The amplifier shall be safe when driving any kind of load—even highly reactive ones. The power requirements shall be 120 VAC at 60 Hz. At idle, the amplifier shall draw 90 watts or less. The amplifier chassis shall be constructed of steel with a durable black finish and shall be designed for flow-through fan-assisted ventilation from the front panel to the side panels. The amplifier shall have an aluminum front panel with super-gloss Imron finish and Lexan overlay. The dimensions of the amplifier shall allow for 19 inch (48.3 cm) EIA standard (RS- 310-B) rack mounting. The amplifier shall be 7 inches (17.8 cm) tall, 16 inches (40.6 cm) deep behind the rack-mounting surface, and 2.75 inches (7 cm) in front of the rack-mounting surface. The amplifier shall weigh 60 pounds, 11 ounces (27.6 kg) and shall have a center of gravity approximately 6 inches (15.2 cm) behind the front panel. The amplifier shall be designated the Crown Studio Reference Learn More

Mcintosh MC7150 sold ? 4/23 Learn More

Threshold SA/3 50watt/channel Stasis Pure Class A Power Amplifier. This amplifier, designed by Nelson Pass and Built in the USA by Threshold employs pure Class A circuitry at every stage - there is no corrective feedback loop Learn More

Goldmund VSR Mononoblock Power Amplifiers Silver Faceplate Great Condition Learn More

Mark Levinson No. 27 Stereo Power Amplifier Power output: 100 watts per channel into 8Ω (stereo) Frequency response: 4Hz to 122kHz Total harmonic distortion: 0.1% Gain: 26 dB Dimensions: 444.5 x 407.8 x 185.6mm Year: 1989 75Lbs Learn More

Krell KSA80B One owner all original excellent condition We can recap for $500 additional if desired before shipping. Later balanced version Learn More

Krell Altair Reference $5500 low profile amplifier with separate power supply from the 1990's. Original boxes Designed as a reference amplifier for apartment sized systems. Power suppy caps just recapped. IN REPAIR Learn More

Goldmund A2 modules (original, new gold) I purchased these sequential modules from the former Goldmund distributor they are a NOS (new old stock pair) Learn More

Audio Research SD135 excellent condition, original box $5000 retail in 1/23 Learn More

Power output: 250 watts per channel into 8Ω (stereo), 1000 watts into 8Ω (mono) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.1% Input sensitivity: 1.6V Signal to noise ratio: 100dB Speaker load impedance: 4Ω (minimum) Dimensions: 19 x 20.75 x 8 inches Weight: 65lbs Learn More

These have the upgraded black circuit boards with high end caps from symphonic line, high quality parts internally. these are cut and paste from the web specs I found. Hope they are accurate 1 x 110 Watts RMS @ 8 Ohms (each) 2 Ohm load stable Class A/AB 1 - 600,000 Hz frequency range 120,000µF memory (each) 120 amps current delivery <0.04% THD (not audible) >800 continuous damping factor Input impedance 22K ohms DC offset <1 mV RCA inputs 400 VA Plitron transformer (each) Sanken Epitaxial Planar Transistors 2SA1216 & 2SC2922 Anti vibration dual thickness PCB Power consumption when idle ±30Watts 4 internal fuses 250V/6.3A, 5x20mm, fast blow 18"W x 16"D x 4 1/4"H weighs 32 pounds. Learn More

PA1230R Integrated Amplifier At a time when many manufacturers are using microprocessor technology to bury functions below several software layers so you need to have an owners’ manual close at hand if you want to access them, T+A has delivered an amplifier where each function has its own control, properly and clearly labelled, on the front panel. This necessarily means there are quite a few knobs and buttons, but rarely has an amplifier been so easy to use. This is especially the case because the PA1230R is one of the very few amplifiers available that allows you to adjust bass and treble individually for the left and right channels. Learn More

sold 12/23 another kav500/5 available 1/24 Krell KAV-500/5 Krell KAV-500 Multichannel Amplifier 100 Watts/Channel into 8 Ohms, 200 Watts into 4 Ohms 400 Watts/Channel bridged (2 channels) Mfr FR 20 Hz - 20 kHz ± 0.5 dB THD < 0.03% Input Impedance 100 kOhms Size: 6.25" H x 19" W x 17" D Weight: 47 pounds Learn More

Mcintosh 2205 just recapped replaced amp coupling caps Original owner on all. Wood case $350 plus shipping extra. Power output: 200 watts per channel into 8Ω (stereo), 400W into 8Ω (mono) Frequency response: 10Hz to 100kHz Total harmonic distortion: 0.1% Damping factor: 16 Input sensitivity: 0.75V Signal to noise ratio: 95dB Speaker load impedance: 1Ω to 8Ω Learn More

Perreaux PMF5150B Learn More

Damping factor into 8 36 Signal to noise ratio ref 100W 8 A-weighted 111dB Signal to noise ratio ref 1W 8 A-weighted 91dB Input signal for clipping 1V RMS Peak current into 1 (1kHz 1mS) +/-28 amps peak (780W peak power) Burst power 2 300 Watts 2 @1% THD+N (1kHz for 20mS, repeat 500mS IHF) Audio Inputs 2 x True balanced via XLR, 47k 34k singled ended via legacy adaptor lead Audio Outputs Crosstalk 60 dB THD + N at 2/3rds full power 8 @1kHz (0.013%) Power Output 100 Watts 8 @0.1% THD+N (100W @0.1%) 190 Watts 4 @1% THD+N Frequency Response -3dB @ 1.4Hz to 100kHz Gain +29 dB Physical Weight 37.04lbs (16.8kg) Dimensions (HxWxD) 35/8x17x121/2" (9.15x43.2x31.75cm) Power Mains Supply 115V or 230V, 50/60Hz Power Consumption Passive consumption: 26W (idle) Standby consumption: <0.5W Product Type Type Power Amplifier Learn More

Krell KAV-2250 silver with box last one, inquire to make sure still available Learn More

Parasound Halo A21 2 Channel Power Amplifier Continuous power output: 250 watts RMS x 2, 20 Hz - 20 kHz, 8 Ω, all channels driven 400 watts RMS x 2, 20 Hz - 20 kHz, 4 Ω, all channels driven 750 watts RMS x 1, 20 Hz - 20 kHz, 8 Ω Current capacity: 60 amperes peak per channel Power bandwidth: 5 Hz - 100 kHz, +0/-3 dB at 1 watt Total harmonic distortion: < 0.2 % at full power IM distortion: balanced 16 V rms < 0.04 % Slew rate: > 130 V/µsecond Dynamic headroom: > 1.5 dB Interchannel crosstalk: > 80 dB at 1 kHz; > 63 dB at 20 kHz Input sensitivity: 1 V for 28.28 V, THX Reference Level Input impedance: 33 k Ω unbalanced; 66 k Ω balanced S/N ratio: 112 dB, input shorted, IHF A-weighted Damping factor: > 1100 at 20 Hz Voltage: 110V - 120V Dimensions: 17-1/2" w x 7-5/8" h x 20" d, 7" h without feet Net weight: 60 lb. Learn More

Nakamichi Stasis PA 7 Stereo Power Amplifier Power output: 200 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.1% Damping factor: 60 Input sensitivity: 2V Signal to noise ratio: 120dB Semiconductors: 16 x output transistors per channel Dimensions: 435 x 200 x 421mm Weight: 27kg Learn More

Meridian G57 amplifier ( 3available) as of 4/23 Learn More

Bryston 4B e 4be (commercial version , balanced looks like 4bst to me) 2 available 2/22 used in a home only Learn More

Plinius 8200P MKII stereo amplifier (4 available) Learn More

Mark Levinson ML9 in beautiful condition we can convert to a voltage other than 120v if you need Learn More

Plinius 8200P Stereo Power Amplifier Black Very Good Condition Learn More

Threshold S200 Power Amp Silver Power output: 100 watts per channel into 8Ω (stereo) Frequency response: 7Hz to 100kHz Total harmonic distortion: 0.1% Gain: 26.6 dB Signal to noise ratio: 100dB Semiconductors: 8 x transistors per channel (output) Dimensions: 8.72 x 19 x 9.125 inches Weight: 44lbs Year: 1984 Learn More

Mark Levinson ML11 power amplifier . With its 2 x 50W in a small enclosure with the heat sinks hidden inside makes it look shy, but it's not. It another great amplifier of MLAS which is perfect as an all-purpose home hifi amplifier. As the others he can drive almost any load. Specifications Power output: 2 x 50W. Weight: 11Kg Maximum power : 260W. Learn More

Pioneer Series 20 M-22 Learn More

SUMO The Nine + Differential Power Amplifier Sumo gives you the real thing. The nine is a pure class A power amplifier that remains class A even when driving 4 Ohm loudspeakers. The Nine's approach to class A is so unique it earned a US patent - an amazing achievement for an audio component. Sumo's exclusive class A engineering provides all the advantages and none of the disadvantages of typical class A designs. The unit features an all aluminium anodized chassis with massive extruded heat sinking and built in whisper fan for efficient heat dissipation. Military grade G-10 glass epoxy printed circuit boards throughout. Power supply incorporating 1.4KW shielded toroidal transformer and 42,000 microfarad computer grade filter capacitors, resulting in supply voltage regulation better than 3%. Learn More

Bedini BA-803 2 available excellent cosmetics, unused last twenty years. Original boxes. 250 watts Class A Operation Learn More

Audio Alchemy DPA-2 black NEW 325 watts/channel Factory sealed new $2500 retail Power Output/Channel (1% Thd+N, 1 Khz): (Stereo 325W/ch @ 4Ohms) / (Mono 625W @ 8Ohms) Frequency Response: 5hz-20khz +/- 0.2dB Nominal Thd+N (1 Watt Into 8Ω): 0.003% Signal-to-Noise Ratio (1 Khz): 94dB Input Impedance: RCA=12K, XLR=19K Output Impedance: 0.03 Ohms @ 1KHz Channel Separation (1 Khz): 70dB @ 1KHz / n/a Gain: Stereo 24dB/30dB – Mono 18dB/24dB Inputs: Unbalanced RCA, Balanced XLR Outputs: Binding post 5-way Available Finishes: Black Dimensions (HxWxD) In: 02.00 x 17.50 x 15.00 including jacks Net Weight: 14.00 lbs The Alchemy DPA-2 Power Amplifier is about dynamic musicality, thanks to design that combines Class A circuit topology composed of discrete FETs and a linear power supply using a toroidal transformer. The pure analog input stage preserves all the detail and nuance of the most delicate passages. The Class D output stage with switching power supply results in impressive output combined with cool-running efficiency. Learn More

solid state amplifier, unused in over 20 years, very nice condition, tech checked 11/16 50 watts per channel minimum RMS (both channels operating) at 8 ohms from 1 Hz to 20 kHz with less than .25% total harmonic distortion. Typically less than .02% at rated power in midband. Approximate actual power available per channel at "clipping" (both ch. op.): 80 (4 ohms), 60 (8 ohms), 35 (16 ohms) Power bandwidth Frequency response 0.05 Hz to 100 Khz (-3 db) Input sensitivity 1.1 Volts RMS for rated power and load. Input impedance 30 Kohms (nominal). Output taps Output regulation Overall negative feedback Damping factor More than 500 at rated power and load (20 Hz to 20 kHz). (Effective internal impedance approximately .012 ohms.) Distortion Intermodulation distortion: Less than .1% at rated output (56.56 V p to p) and load (SMPTE method). THD and IMD both decrease with decreasing output. Slew rate Rise time Hum & noise Wide-band, unweighted, more than 90 dB below 50 watts at 8 ohms - power line components (hum) more than 80 dB below 50 watts at 8 ohms. Power supply energy storage Power requirements 105-120/210-240 VAC, 50/60 Hz, 600 watts maximum. 120 watts at idle. 300 watts at rated power. Other Dimensions 19" (48 cm) W x 5 ¼" (13 cm) H (standard rack mount panel size) x 10 ½ (26.7 cm) D (front panel back). Handles extend 1 ½" (3.8 cm) forward of the front panel. Weight 39 lbs. (17.7 kg) Net, 45 lbs. (20.5 kg) Shipping Learn More

Bryston 4b thx version Just recapped for like new sound and reliability Learn More

Crown D-150 excellent like new condiition Was in a rack since new. Learn More

Lexicon 501 same as Bryston 7Bst 500 watts/channel one mono amplifier Learn More

Kenwood L-07 For repair, selling the pair as is classics Power output: 150W into 8Ω (mono) Frequency response: 1Hz to 50kHz Total harmonic distortion: 0.008% Damping factor: 100 Input sensitivity: 1V Signal to noise ratio: 120dB Speaker load impedance: 4Ω to 16Ω Dimensions: 200 x 155 x 390mm Weight: 13kg Learn More

Crown SA 2 Distinction Series Amplifier Very Good Condition Learn More

Power output: 60 watts per channel into 8Ω (stereo) Frequency response: 10Hz to 60kHz Total harmonic distortion: 0.1% Damping factor: 150 Input sensitivity: 1V Signal to noise ratio: 90dB Learn More

Marantz 15 Learn More

Nakamichi Stasis PA5 Amplifier Power output: 100 watts per channel into 8Ω (stereo) Frequency response: 7Hz to 150kHz Total harmonic distortion: 0.1% Damping factor: 60 Input sensitivity: 1.4V Signal to noise ratio: 120dB Speaker load impedance: 4Ω to 16Ω Semiconductors: 20 x transistors Dimensions: 435 x 135 x 368mm Weight: 16kg Learn More

Rotel RB-1582 200 watts/channel Learn More