Product Description
Details
Connection elements
GND The ground lead from an analogue disc player is connected here in
order to avoid hum.
TUNER Input sockets for connecting high-level signal sources such as tuner.
CD Input sockets for connecting high-level signal sources such as CD
player.
AUX 1 General-purpose pre-amplifier inputs with an input sensitivity of
250 mV / 20 kΩ .
AUX 2 General purpose pre-amplifier input with an input sensitivity of 250
mV / 20 kΩ . If an MM or MC phono module is fitted then AUX 2 is the
phono input.
With MM phono module: Input socket for disc players with moving
magnet (MM) cartridge systems. Input capacitance (100 pF ... 500 pF)
and input sensitivity (1 mV ... 5 mV) variable by means of switches.
Simply set the values closest to those stated by the cartridge
manufacturer.
With MC phono module: Input socket for disc players with moving
coil (MC) cartridge systems. Input impedance (5 Ω ... 650 Ω ) and
input sensitivity (50 uV ... 1000 uV) variable by means of switches.
Simply set the values closest to those stated by the cartridge
manufacturer.
TAPE 1 Input and output sockets for connecting devices which can record and
play back (recorders).
PA 1230 R
TAPE 2 Input and output sockets for connecting devices which can record and
play back (recorders).
The input is equipped with an input buffer to be connected to source
units with high output impedance (>1kΩ ).
TV Input sockets for connecting high-level signal sources such as TV or
VCR. The input is equipped with an input buffer to be connected to
source units with high output impedance (>1 kΩ ).
PRE Variable asymmetrical pre-amplifier output fitted with cinch sockets.
As this is a very low impedance output it is suitable for long leads (e.g.
to connect active speakers).
SPEAKER A + B Two pairs of loudspeakers can be connected to the amplifier
(SPEAKER A and SPEAKER
RC-IN Input socket for the E 2000 remote control receiver.
RC-OUT The remote control signals are transferred to the source devices via
the remote control leads RZ 001, which are plugged into the RC-OUT
sockets.
RLink Control output – preparation to control futur "R"-system components
with extendend functions. A software update may be necessary.
TASI Connection to T+A Surround decoder.
Specifications
Pre-amplifier
Frequency response + 0 – 3 dB 0,5 Hz – 400 kHz
Signal: noise ratios (A-weighted)
High level 87 x 104 / 109 dB
Phono MM 82 / 86 dB (Non-standard version)
MC 78 / 82 dB (Non-standard version)
Sub-sonic filter fixed (Non-standard version)
Total harmonic distortion < 0,001 %
Intermodulation < 0,001 %
Channel separation > 90 dB
Nominal input sensitivity
High level 250 mV / 20 kOhms
MM 1 – 5 mV
16 capacitances
MC 60 – 1000 uV
16 impedances
Outputs
Headphones 50 Ohms
2 x Tape 250 mV / 100 Ohms
PRE out Cinch nominal 1 V eff
max. 9,5 V eff
Impedance 22 Ohms
Dolby surround interface with fixed level (TASI) present
Output stage
Nominal output 8 Ohms 100 Watt
per channel 4 Ohms 150 Watt
T+A - Produktarchiv PA 1230 R
Peak output 8 Ohms 150 Watt
4 Ohms 290 Watt
Power bandwidth 1 Hz – 300 kHz
Frequency response + 0 – 3 dB 1 Hz – 400 kHz
Slew rate 60 V/us
Damping factor > 500
Signal: noise ratio (A weighted) > 110 dB
Total harmonic distortion < 0,002 %
Reservoir capacity 50000 uF
Mains supply 110 V or 220 / 240 V, 50 Hz 300 VA
Dimensions 7,5 x 44 x 39 cm
Additional Information
Additional Information
| Call For Price | No |
|---|