solid state

Goldmund 8.5 with a2 modulesSolid-state stereo power amplifier. Learn More

Bryston 6b Stereo Amplifier Learn More

Mcintosh MC2500 in 10/24 will be recapped and cosmetically restored before shipping. freight shipping inquire. Learn More

Meridian 857 two years old when we received as new condition in original packaging. "Our most powerful reference two channel amplifier has been designed and built to deliver the best possible Hi-Res audio performance from any high-quality passive loudspeaker system. Its low-feedback construction provides ultra-low distortion, ensuring an unparalleled level of clarity and transparency across the audible range. Bridgeable to over 1.5Kw, the Meridian 857 features a totally new design for a Meridian power amplifier, borne out of extensive research, experience and a thorough understanding of psychoacoustic principles." Learn More

Krell Evolution One 4 chassis amplifier in factory boxes, like new The most beautiful Krell amps ever made. Inquire for freight options Learn More

Krell FPB300c As of 6/24 one Unit is currently at the Krell factory, one is at our Florida showroom. Unit recently recapped. These typically will be trucked, not sent fedex or ups van for $250-$300. Please inquire with your postal code. Learn More

Krell Trigger Converter 12pin in to 5 pin out Learn More

Mark Levinson 33h mono pair recapped all caps except large filter capacitors (rarely go bad, long life) and changed the relays. 9/2023 custom crated, inquire for freight options Learn More

Krell 402 silver (1 available 6/22) We can provide this in any voltage worldwide. Black (1 available 11/22) Learn More

Bedini BA-803 2 available excellent cosmetics, unused last twenty years. Original boxes. 250 watts Class A Operation Learn More

Kenwood L-07M Just serviced 9/24 classics Power output: 150W into 8Ω (mono) Frequency response: 1Hz to 50kHz Total harmonic distortion: 0.008% Damping factor: 100 Input sensitivity: 1V Signal to noise ratio: 120dB Speaker load impedance: 4Ω to 16Ω Dimensions: 200 x 155 x 390mm Weight: 13kg Learn More

Plinius 8200P MKII stereo amplifier (4 available) Learn More

PS Audio 200C (3 available) we need to service/upgrade these before shipping Learn More

Goldmund A2 modules (original, new gold) I purchased these sequential modules from the former Goldmund distributor they are a NOS (new old stock pair) Learn More

Lexicon 501 same as Bryston 7Bst 500 watts/channel one mono amplifier Learn More

You can purchase each item individually. We have one 120 that we just replaced the coupling caps and resoldered the board as needed. That's $250 Inquire The Dynaco Stereo 120 is an all silicon transistor basic power amplifier for use with separate preamplifiers such as the Dynaco PAT-4 or PAT-5, or for use with tape recorders or tuners such as the FM-5 or AF-6, which have their own volume controls. The unit contains two 60 watt amplifiers on one chassis with a common power supply. Although the Stereo 120 is a solid state device, containing transistors and similar semiconductors, it has been designed to be used under normal conditions without special safety precautions, just as if it were a high grade tube amplifier. Thus it can be connected to source and speaker components and used with confidence in all conventional arrangements. There are no circuit breakers, speaker fuses, or other resettable devices to impede the use of the Stereo 120 under any reasonable conditions of use or abuse. This is achieved by using novel circuits (on which patents are pending) which automatically and instantly protect the amplifier. Specifications Power output: 60 watts per channel into 8Ω (stereo) Frequency response: 5Hz to 100kHz Total harmonic distortion: 0.5% Damping factor: 40 Input sensitivity: 1.5V Signal to noise ratio: 95dB Speaker load impedance: 4Ω to 16Ω Semiconductors: 15 x transistors, 15 x diodes Dimensions: 13 x 10.5 x 4 inches Weight: 20lbs Learn More

Krell FPB600 just recapped 12/23 excellent cosmetics We will crate this for shipment outside of the I95 corridor for an extra $225. 225lb shipping weight, inquire for freight options sold Learn More

Mcintosh MC611 single mono amplifier only one available factory box cord and manual, like new condition Learn More

solid state amplifier, unused in over 20 years, very nice condition, tech checked 11/16 50 watts per channel minimum RMS (both channels operating) at 8 ohms from 1 Hz to 20 kHz with less than .25% total harmonic distortion. Typically less than .02% at rated power in midband. Approximate actual power available per channel at "clipping" (both ch. op.): 80 (4 ohms), 60 (8 ohms), 35 (16 ohms) Power bandwidth Frequency response 0.05 Hz to 100 Khz (-3 db) Input sensitivity 1.1 Volts RMS for rated power and load. Input impedance 30 Kohms (nominal). Output taps Output regulation Overall negative feedback Damping factor More than 500 at rated power and load (20 Hz to 20 kHz). (Effective internal impedance approximately .012 ohms.) Distortion Intermodulation distortion: Less than .1% at rated output (56.56 V p to p) and load (SMPTE method). THD and IMD both decrease with decreasing output. Slew rate Rise time Hum & noise Wide-band, unweighted, more than 90 dB below 50 watts at 8 ohms - power line components (hum) more than 80 dB below 50 watts at 8 ohms. Power supply energy storage Power requirements 105-120/210-240 VAC, 50/60 Hz, 600 watts maximum. 120 watts at idle. 300 watts at rated power. Other Dimensions 19" (48 cm) W x 5 ¼" (13 cm) H (standard rack mount panel size) x 10 ½ (26.7 cm) D (front panel back). Handles extend 1 ½" (3.8 cm) forward of the front panel. Weight 39 lbs. (17.7 kg) Net, 45 lbs. (20.5 kg) Shipping Learn More

Linn Knekt-A 3 available price is for each Learn More

Cello HTA-3 channel amplifier 200 watts / channel x 3 channels, rare Learn More

Mcintosh 2205 just recapped replaced amp coupling caps Original owner on all. Wood case $350 plus shipping extra. Power output: 200 watts per channel into 8Ω (stereo), 400W into 8Ω (mono) Frequency response: 10Hz to 100kHz Total harmonic distortion: 0.1% Damping factor: 16 Input sensitivity: 0.75V Signal to noise ratio: 95dB Speaker load impedance: 1Ω to 8Ω Learn More

Krell KMA-i800 Reference Monoblocks Axpona show demos inquire for special pricing. (888)850-4366 Will ship directly from Krell factory to you, full new warranty Learn More

Krell KAV-2250 silver very nice condition Learn More

Krell Altair Reference $5500 low profile amplifier with separate power supply from the 1990's. Original boxes Designed as a reference amplifier for apartment sized systems. Power suppy caps just recapped. IN REPAIR Learn More

Parasound JC1 pair price includes shipping price for each to ship Learn More

Mark Levinson 383 with remote two available as of 5/24 Learn More

Spectral DMA250, used factory carton, I can voltage convert prior to shipping. INQUIRE IF STILL AVAILABLE BEFORE PURCHASING. http://www.spectralaudio.com/dma-250.htm SPECIFICATIONS DMA-250 Stereo Power Amplifier Power Output: (continuous) @ 8 ohms - 200 Watts RMS @ 4 ohms - 350 Watts RMS @ 2 ohms - 570 Watts RMS Output Current: 60 Amps peak per channel Frequency Response: ±0.1 dB, DC-150 KHz ±1 dB, DC-1 MHz ±3 dB, DC-1.8 MHz Distortion: Static: Less than 0.015% from DC to 100 KHz, typically 0.009% @ 200 WRMS/8 ohms Dynamic: 8 Tone Cluster Test 20 KHz @ 500 Hz separation; 0.01% 8 ohms; 0.015% 4 ohms Speed: Rise Time: Less than 400 nanoseconds Settling: 1.5 microseconds to -40dB Slew Rate: 600 volts/microsecond Noise: Signal to Noise: 97dB unweighted, 107dB ASA A Crosstalk: 98dB @ full power 8 ohms Input: Impedence: 100K ohms in parallel with 100 pf Sensitivity: 1.5 volts/nominal output Power Supply: Line Voltage: 100 volts, 120 volts, 240 volts (factory set) AC Voltage Range: ±10% Maximum Consumption: 1600 Watts Quiescent Consumption: 250 Watts Operating Temp: 0° to 50° Celsius range; 32° to 122° Farenheit Protection Features: DC Protection Servo: 0.5 volt range Current Limit Onset: 60 Amps Thermal Threshold: Protects at 85° Celsius, 185° Farenheit AC Main Fuses: 2 @ 2-1/2A 3 AG slo-blo, for 100 - 120 VAC 2 @ 1-1/4A 3AG slo-blo, for 220-240 VAC Size and Weight: Dimensions: 48.22cm (19")W x 18.4cm (7 1/4")H x 45.8cm (18")D Weight: 62 lbs, 28.1 KG Net Learn More

Bryston 4B e 4be (commercial version , balanced looks like 4bst to me) 2 available 2/22 used in a home only Learn More

Threshold SA/3 50watt/channel Stasis Pure Class A Power Amplifier. This amplifier, designed by Nelson Pass and Built in the USA by Threshold employs pure Class A circuitry at every stage - there is no corrective feedback loop Learn More

Almost no use, this is the top of the line Stax headphone amplifier in the original double box The SRM-T8000 is STAX new designed top-of-the-line driver unit. For the first time in STAX driver unit history, the large-sized toroidal transformer and non-magnetic aluminum chassis have been adopted for unclouded clear tone quality! A newly developed large-sized aluminum insulator, combined with new material of high isolation efficiency and grip power, make this flagship designed SRM-T8000 a top performer. Features: • The full-balanced transmission of hybrid amplifier configuration with 6922 dual triode tube of established reputation for the first stage and class-A operating semiconductor at output stage realized ultra low-noise, accurate and rich musical expression. • The vacuum tube of the first stage was mounted on the independent board in order to shut out vibration and external noise. Further, noise has been totally eliminated by vibration-proofing damper and vacuum tube shield cover which are used also for a hard disk etc. • The large-sized toroidal transformer - for the first time in STAX driver unit history - as well as non-magnetic aluminum chassis has been adopted for unclouded clear tone quality. • Four pairs of inputs are equipped. (Notes: LINE4 is an optional slot for future purpose. As for now, release is not yet determined.) • The SRM-T8000 features the EXTERNAL (BYPASS) function which passes the volume controller of the unit and enables volume control through external equipments. • The newly developed large-sized aluminum insulator, combined with new material of high isolation efficiency and grip power, has been employed. Specifications: Frequency response: 1Hz - 115kHz / when used with one earspeaker Rated input level: 100mV (at 100V output) Maximum input level: 30Vrms. / at minimum volume Gain: 60dB Harmonic distortion: 0.01% or less / 1kHz / when used with one earspeaker Input impedance: 50kO / 50kOx 2 (XLR input) Maximum output voltage: 470Vrms Mains voltage: AC120V, 50/60Hz Power consumption: 58W (95W with optional slot) Operating temperature: 0 to 35 degrees C (less than 90% humidi- ty, non condensing) Dimension: 320 (W) x103 (H) x395 (D) mm (protruding portion included) Weight: 7.3kg Learn More

excellent condition Mark Levinson 23 200 watt/channel amplfiier, 100V set at present, can be changed Description: Solid-state stereo power amplifier. Rated power output: 200Wpc continuous into 8 ohms (23dBW) with less than 0.1% THD, 400Wpc continuous into 4 ohms (23dBW) with less than 0.2% THD, both from 20Hz–20kHz, both channels driven. Damping factor: greater than 600 at 50Hz, 8 ohms (equivalent to an output impedance of 0.013 ohms). Frequency response: 4Hz–140kHz, —dB. Input impedance: 50k ohms shunted by 1.5nF. Voltage gain: 26dB (load not defined). Input sensitivity: 141mV for 1W output. Dimensions: 19" (483mm) W by 8.25" (210mm) H by 15.7" (399mm) D. Shipping weight: 105 lbs (48kg). Learn More

Krell FPB350mc one mono amp only excellent condition best shipped by truck, inquire Learn More

Krell KSA-i400 NEW REFERENCE! IN STOCK! Please inquire for pricing and for trade-ins at (888)850-4366 We have a used black one in 2/25 for $17000 and new in stock. Learn More

Pioneer Series 20 M-22 Learn More

Anthem P2 retail $4500 in very good condition Learn More

Mark Levinson ML11 power amplifier . With its 2 x 50W in a small enclosure with the heat sinks hidden inside makes it look shy, but it's not. It another great amplifier of MLAS which is perfect as an all-purpose home hifi amplifier. As the others he can drive almost any load. Specifications Power output: 2 x 50W. Weight: 11Kg Maximum power : 260W. Learn More

Krell Evolution 600 monos in 10/24 inquire for factory service by Krell (that's my other business) These must be shipped by truck only, inquire with your postal code. Learn More

Perreaux PMF5150B Learn More

Mark Levinson No 433 with box/packing. Not used last ten years Learn More

PS Audio Delta 100 Learn More

Krell FPB300 recapped Learn More

Mcintosh MC7270 One in excellent 8/22 One in service 6/22 awaiting new factory glass, main output filter caps will be changed out also. Original box from Mcintosh if shipped, inquire for freight cost Too fragile for Fedex or UPS ground. Learn More

Mcintosh MC2300 rare gold faceplate In 9/22 we will recap this unit before shipping pics soon Learn More

Hafler DH500 purchased from original owner in 12/24 Learn More

Naim NAP 555 in from original owner 12/24 Learn More

Krell Evolution 400 Mono Learn More

Crown D-150 excellent like new condiition Was in a rack since new. Learn More

Krell FPB300cx factory recapped 2025 (I run Krell's factory service now) amp will ship from Orange, CT to you Learn More

Marantz 16 Learn More

Halcro DM68 upgrade servicing (caps) 1/19 black pair , top of the line worldwide voltage inquire for actual trucking charges sold Learn More

Linn solo 500 with boxes in 4/25 very good condition Learn More

Krell FPB350MC monos with cast in 10/24 pair pics soon inquir for shipping options Learn More

Audio Research SD135 excellent condition, original box $5000 retail in 1/23 Learn More

Adcom GFA5400 in and serviced 8/24 Learn More

Jeff Rowland Research Model 3 Learn More

Marantz MM7025 used excellent About this product Product Information The Marantz MM7025 is a 2-channel amplifier that is sure to boost the performance of your audio system. With a power output of 140 watts, this Marantz amplifier makes sure that you experience a power-packed performance. The 8 Hz - 100 kHz frequency response range of this 2-channel amplifier provides you with crisp highs and a tight bass response. With a signal-to-noise ratio of 105 dB, this Marantz amplifier reproduces even the minutest of musical detail with reduced background noise. The Marantz MM7025 features RCA and balanced XLR inputs to provide complete system compatibility, without the need of a preamplifier or a processor. Learn More

Crown K1 Balanced Current Amplifier (3 available) as of 9/24 consumer used only Crown K1 Amplifier at a Glance: Balanced Current Amplifier technology ensures thermal stability without a fan! Delivers 350 watts at 8 Ohms, up to 1500 watts (bridged) at 4 Ohms Incredibly flat frequency response for compromise-free audio Massive power with one tenth the heat! The K1 amp from Crown is the first amplifier to take advantage of Crown's new Balanced Current Amplifier technology. This technology yields extremely efficient power amplification while generating just one-tenth the heat of conventional amplifiers. In fact, the powerful K1 Amplifier can deliver an amazing 750 watts per channel into 2 Ohms (and that's a very solid 2 Ohms)! As a result the amp can put out clean, uncolored power without the use of a fan. No fan means the K1 runs quietly and cleanly, takes up less space in a rack and requires less maintenance. The K1 also boasts advanced circuitry protection that guards against DC, mismatched loads, internal faults and high frequency overloads. Crown is so confident of the K1's stability that it's backed by a three-year no fault warranty! Power to spare, no matter what your configuration The Crown K1 Amplifier is rated to deliver 350 watts per channel at 8 Ohms, 550 watts into 4 Ohms or 750 watts per channel into 2 Ohms. In addition, in bridged mode the K1 has a capability of 1100 watts at 8 Ohms or 1500 watts at 4 Ohms - all while running without a fan! The K1 is cool, clean and quiet. Legendary Crown frequency response Crown amps have a long history of providing crystal-clear audio response in critical listening situations, and the K1 Amplifier is no exception. Flat frequency response: (+/- .25 dB) from 20Hz to 20kHz ensure you get out of the K1 exactly what you put into it! Crown K1 Amplifier Features: Soft Start (Keeps amp from drawing large currents when first turned on) Switchable Input Sensitivity (1.4V or 26dB) Mono mode switches: Bridged, Y (parallel) or both (for daisy chaining) Balanced XLR and 1/4" inputs 5-way binding posts Channel 1 and Channel 2 gain controls with notched settings LEDS: Thermal (Warns of need to dissipate heat), Clip (Warns of distortion in the amp), IOC (Input / Output Comparator: Warns of distortion at 1/30th the level of clipping by comparing the actual waveforms of the input to the output), Signal (glows when output signal is present), Enable (Indicates Power status) Frequency Response: +/- .25 dB for 20Hz - 20kHz Power Output (per Channel): 750 watts into 2 Ohms, 550 watts into 4 Ohms, 350 watts into 8 Ohms Bridged (mono) power: 1500 watts at 4 Ohms, 1100 watts at 8 Ohms Signal-to Noise (A Weighted): >100dB below rated power Damping Factor: >3000 from 10 to 400Hz Input Impedance: Nominally 20KOhms balanced, 10KOhms unbalanced Passive convection cooling allows amplifier to drive 2 Ohm load at 8db into clip in 104 degree environment! Power Supply can configure to 100, 120, 200, 220, 230, 240, 250 VAC at 50 or 60 Hz Learn More

Mcintosh MC2505 in beautiful condition, one owner in 3/23 New box and packing ordered from Mcintosh 3/23 optional wood case pictured $350 additional plus shipping Learn More

Crown Reference 1 in service 9/21 Inquire before purchasing Reference I (120 V, 60 Hz models) The Crown® Studio Reference I power amplifier shall be a solid-state two-channel model employing multi-mode (AB+B) grounded bridge(TM) output circuitry with a variable impedance (VZ) power supply for each channel. The outputs shall be switchable as stereo, bridged-mono or parallel-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. The parallel-mono mode shall parallel the outputs to provide increased output current. The output impedance of each channel shall be less than 10 milliohms in series with less than 2 microhenries in stereo mode. The variable impedance power supplies shall reduce unnecessary voltage across the output devices by automatically switching to a parallel mode when less voltage is required by the output circuitry and to a series mode when more voltage is required. The amplifier shall contain protection circuitry which limits the drive level placed on the output devices before their SOA (Safe Operating Area) is exceeded. This protection circuitry shall calculate the instantaneous voltage across and current through the output devices while factoring in their simulated junction temperatures to predict how close they are to their operating limits. This protection will be called “ODEP.” The amplifier shall contain controlled slew-rate voltage circuitry to protect it against radio frequency interference burnouts. It shall also be protected from current overload at its output stage. The slew rate of the amplifier shall be greater than 30 volts per microsecond in stereo mode. The amplifier shall temporarily go into a stand-by mode if its power transformer becomes excessively hot and shall automatically resume normal operation once it has cooled to a safe operating temperature. Front-panel controls shall include an enable on/off switch and a detented input level control for each channel. Rear-mounted controls shall include a ground lift switch to isolate the signal ground from the chassis ground, a switch which selects between stereo, bridged-mono and parallel-mono modes of operation and a reset switch for the AC mains circuit breaker. Internal controls shall include an input sensitivity switch to select between 0.775 V, 1.4 V or a fixed voltage gain of 26 dB for full rated output. A Crown P.I.P. and P.I.P.2-compatible expansion connector shall be provided behind an access panel in the rear to accept auxiliary input modules. It shall be fully compatible with the Crown IQ System. Front panel indicators shall include an amber power enable indicator, an amber ODEP protection system indicator for each channel which shall normally be illuminated to confirm the availability of reserve thermodynamic energy and which shall dim in proportion to limiting when the power demands of the output stages have been exceeded, a green IOC indicator for each channel, and a green Signal indicator for each channel which shall normally flash at moderate intensity to show the presence of an audio signal. The power amplifier shall meet or exceed the following performance criteria. Input sensitivity for rated output: 26 dB voltage gain (unbalanced). Rated FTC output in stereo mode with less than 0.1% THD: 780watts per channel (20 Hz to 20 kHz) into 8 ohms. Hum and noise: at least 120 dB (A weighted) below full rated output power. Phase response: +5 to –15 degrees from 20 Hz to 20 kHz at 1 watt. Frequency response: 20 Hz to 20 kHz, 0.1 dB at 1 watt into 8 ohms per channel in stereo mode. Damping factor: greater than 20,000 from 10 to 200 Hz into 8 ohms. Intermodulation distortion (SMPTE): less than 0.005% from full bandwidth power to 78 watts rising linearly to better than 70 dB at 20 kHz. Harmonic distortion: less than 0.02% at rated low-distortion 1 kHz power. The amplifier shall be safe when driving any kind of load—even highly reactive ones. The power requirements shall be 120 VAC at 60 Hz. At idle, the amplifier shall draw 90 watts or less. The amplifier chassis shall be constructed of steel with a durable black finish and shall be designed for flow-through fan-assisted ventilation from the front panel to the side panels. The amplifier shall have an aluminum front panel with super-gloss Imron finish and Lexan overlay. The dimensions of the amplifier shall allow for 19 inch (48.3 cm) EIA standard (RS- 310-B) rack mounting. The amplifier shall be 7 inches (17.8 cm) tall, 16 inches (40.6 cm) deep behind the rack-mounting surface, and 2.75 inches (7 cm) in front of the rack-mounting surface. The amplifier shall weigh 60 pounds, 11 ounces (27.6 kg) and shall have a center of gravity approximately 6 inches (15.2 cm) behind the front panel. The amplifier shall be designated the Crown Studio Reference Learn More

BelCanto REF600 mono amps 300 watts/channel Learn More

Bryston 4b thx version Just recapped for like new sound and reliability Learn More

Devialet Expert 200, original box/packing, excellent condition Learn More

JBL S400 stereo power amplifier Power output: 200 watts per channel into 8Ω (stereo), 400W into 8Ω (mono) Frequency response: 10Hz to 70kHz Total harmonic distortion: 0.02% Damping factor: 120 Input sensitivity: 1V Signal to noise ratio: 105dB Speaker load impedance: 4Ω (minimum) Dimensions: 5.5 x 19 x 16.5 inches Weight: 45lb Learn More

Balanced Audio Technology VK-250, excellent condition Learn More

Audio Research D400 MKII 200 watts/channel $5995 retail In repair 10/24 inquire as to status we have three of them. Power output 200 watts per channel into 8 ohms, 400 watts per channel into 4 ohms. Power bandwidth D400: (-3dB points): 0.01Hz-160kHz D400 MKII: (-3dB points) 4Hz to 100 kHz Low level: (-3dB points) 0.01Hz to 160kHz. Frequency response Input sensitivity D400: 1.91V RMS for rated output (26.4 dB gain) unbalanced or balanced D400 MKII: 2.0V RMS for rated output (26dB gain) unbalanced or balanced Input impedance D400: 150K ohms normal or invert, 300K ohms balanced differential D400 MKII: 57K ohms normal or invert, 114K ohms balanced differential Output taps Output regulation 0.06dB 8 ohm load to open circuit Overall negative feedback D400: 9.3dB D400 MKII: 9.7dB Damping factor 150 Distortion Slew rate 50V/µs Rise time 1.0 µs Hum & noise D400: Less than 150 µV RMS (106dB below rated output IHF A-weighted) D400 MKII: Less than 220 µV RMS (105dB below rated output IHF A-weighted) Power supply energy storage 270,000 µF Power requirements 105-125VAC 60Hz (210-250VAC 50 Hz) 760 Watts at rated output (200WPC 8 ohms). 1200 watts maximum (400WPC 4 ohms), 220 watts idle Other Peak output current: 60 Amp peak into 1 ohm Input polarity: Non-inverting at normal inputs. Balanced pin 2+ Dimensions 19" (48 cm) W (standard rack panel) x 9" (22.8 cm) (8¾" (22.2 cm) panel + ¼" feet (0.6 cm) H x 17¾" (45.0 cm) D (front panel back). Handles extend 1 and 5/8" (4.1 cm) forward of the front panel. Handles extend 1 and 5/8" (4.1 cm ) behind rear panel Weight D400: 73 lbs. (33.2 kg) Net, 90 lbs. (41.0 kg) Shipping D400 MKII: 76 lbs. (34.5kg) Net, 94 lbs. (42.7 kg) Shipping In service 11/20 Learn More

Naim NAP135 pair of monos 6 pieces available as of 9/24. These will be recapped before sending to you Learn More

Marantz 15 Learn More

B&K Sonata M200 mono pair Learn More

Thule Audio Spirit PA100 power amplifier Thule Audio is a Danish company, specializing in audio equipment, ranging from basic entry level models, to models which are High End stuff. The product line is well thought out, and as we shall see, very rationally conceived and executed. For other reviews of Thule Audio products, look over the site. Both cases are virtually identical, and share the overall look of the entire Thule Spirit range. They are made of uncommonly thick, heavy and well finished cases, while front panels are made from 8mm thick aluminium, machined so that they have a gentle slope. In the center, one will find a "gold" knob in case of the preamp, and a decoration in case of the amp. The preamp has an alphanumeric display above the knob, which provides the user with all relevant information on power on, volume and input status in red LEDs. All this is fully remote controllable, and a remote control unit is supplied. The power amp is a very simple affair, with only a red LED power on indicator on its front side. Both units have rocker power on/off switches at the back, as they're intended to be left in standby mode all the time. [Thule PR 100 inside view] Both units share much more common componentry that I would have imagined. Both use toroidal power supplies, where the amp's toroid is rated at 500VA, while the preamp's toroid is rated at 300VA. No, you're not seeing things, it's not a typo error, I did say 300VA. That's enough for a 2x75W/8 Ohm power amplifier, let alone a simple preamp. In fact, the preamp is EXACTLY the same as the IA60 integrated amplifier, minus the power amp circuitry and heat sinks. Put another way, the preamp consists of the preamp section of the IA60 integrated. Hence the 300VA toroidal transformer - that's what they use in IA60 (see review on this site). The power amp, on the other hand, is once more the same board, but minus the preamp circuitry and with heftier power supplies - bigger transformer, and 4x10.000uF capacitors, instead of just 2x10.000uF. This is no accident, this is rational thinking. Use the same board, use the same case, use the same power supplies and you increase the numbers of your serial production, thus pushing the cost per unit down. The only thing that spoils the show is the preamp's price - it's simpler than the integrated model, but it's not only not cheaper, it's actually somewhat more expensive. That is most odd, I must say - probably for "complex marketing reasons" (a phrase I first heard in the early seventies, and it's gotten worse since then). You still have 5 line level inputs, with no option for a phono RIAA board of any kind. You still don't have a headphone output - somebody should inform the Scandinavian audio industry that headphones have been invented some decades ago, they seem to have collectively overslept that event. As usual, all input and output sockets are gold plated. Like elsewhere in Thule's product portfolio, volume and balance are controlled by a ladder of laser trimmed resistors, contained within an LM1792 digital volume control, a good point - no mechanics, no wear and tear, no aging, unparalleled precision. The amp is rated at 2x100W/8 ohms and 170W/4 Ohms - that should be enough for most of us. It has an RCA Cinch and a balanced XLR input, just as the preamp has the same outputs. Acting on logic and Thule's recommendation, I used balanced lines to link the two, except when using other units. Learn More

Krell FPB650MC Monos factory service recapped 2025 My other business is Krell factory service, so this will be freshly recapped 5/25 before shipping to you inquire for freight options. Learn More

Krell KSA150 fresh recap on one 12/23 2 available the other not recapped excellent cosmetics on that one. Learn More

Dynaco ST 150 power amplifier The Dynaco Stereo 150 is a basic two channel power amplifier employing all silicon semiconductors. They include 24 transistors, 2 zener diodes, 16 diodes, and 2 thermal sensors. The output circuitry is of the full complementary symmetry design. The entire amplifier, except for an input network, is direct coupled. It's measured distortion levels approach the threshold of much laboratory test equipment, not only at the commonly specified full power ratings, but more importantly at very low power outputs as well. This is the result of circuit techniques which eliminate any discernible crossover notch at low levels, and contributes to the Stereo 150's freedom from listening fatigue. It's accurate, uncoloured sonics have been achieved on a wide variety of loudspeaker loads, including electrostatics and multiple drivers with complex crossovers. The design of a very fine power amplifier implies the necessity of several protection techniques for the amplifier, and for the speaker load. In addition to the AC line fuse, four separate B+ fuses are supplied. Electronic volt-amp limiting ensures safe operation of the output transistors, and a thermal sensor mounted directly on each output stage reduces the input if high temperature occurs. An unusually large radiating area for the heat fins, which are coupled to an aluminium back panel, form a highly efficient heat sink. Speaker fuses protect the load. The Stereo 150 has been designed as two independent 75 watts (at 8 ohms) amplifying channels with a common power supply having a high degree of inherent regulation. In addition, where higher powers or higher volt-amp capabilities are required for lower load impedances, easy internal restrapping permits monophonic operation for 150 watts output (at 8 ohms). An accessory kit is planned at additional cost for two output meters and meter switching, which includes alternative inserts for the front panel. Specifications Power output: 75 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.25% Damping factor: 50 Input sensitivity: 1V Signal to noise ratio: 95dB Speaker load impedance: 4Ω to 16Ω Semiconductors: 24 x transistors, 2 x zener diodes, 16 x diodes, 2 x thermal sensors Dimensions: 14.5 x 13.75 x 7 inches Weight: 29lbs Learn More

Rotel RB-1582 200 watts/channel Learn More

Triad Powersub AmpliflierTriad benchtested 5/18 good Learn More

Adcom GFA-535ii bench tested 5/18 Learn More

NAD 916 Amplifier missing power button, works fine Learn More

ADS A2 bench tested 5/18 good Learn More

Mark Levinson ML9 in beautiful condition we can convert to a voltage other than 120v if you need Learn More

Burmester 909 IIIa stereo sold Learn More

Krell KMA100 mono pair (Krell factory recapped 2025) very nice condition I run Krell factory service with my other business. Inquire for freight options Learn More

Krell Audio Standard 2 coming soon 2/22 recapped approximately 3 years ago must ship freight inquire before purchasing please Learn More

Krell MDA400s mono pair just recapped, with meters in boxes Very rare version of the Krell KSA200s KSA300s series in mono Inquire for trucking rate Learn More

Mark Levinson 331 recently serviced by factory authorized center Learn More

Mark Levinson 332 in service 5/24 inquire Learn More

Krell KAV-250a stereo amplifier Learn More

PS Audio BHK 300 monos excellent with original boxes inquire for trucking pricing. I'ts safer Learn More

Audio Alchemy DPA-2 black NEW 325 watts/channel Factory sealed new $2500 retail Power Output/Channel (1% Thd+N, 1 Khz): (Stereo 325W/ch @ 4Ohms) / (Mono 625W @ 8Ohms) Frequency Response: 5hz-20khz +/- 0.2dB Nominal Thd+N (1 Watt Into 8Ω): 0.003% Signal-to-Noise Ratio (1 Khz): 94dB Input Impedance: RCA=12K, XLR=19K Output Impedance: 0.03 Ohms @ 1KHz Channel Separation (1 Khz): 70dB @ 1KHz / n/a Gain: Stereo 24dB/30dB – Mono 18dB/24dB Inputs: Unbalanced RCA, Balanced XLR Outputs: Binding post 5-way Available Finishes: Black Dimensions (HxWxD) In: 02.00 x 17.50 x 15.00 including jacks Net Weight: 14.00 lbs The Alchemy DPA-2 Power Amplifier is about dynamic musicality, thanks to design that combines Class A circuit topology composed of discrete FETs and a linear power supply using a toroidal transformer. The pure analog input stage preserves all the detail and nuance of the most delicate passages. The Class D output stage with switching power supply results in impressive output combined with cool-running efficiency. Learn More

Meridian G57 amplifier ( 3available) as of 4/23 Learn More

B&K ST1400 MK II good cosmetics Learn More

PA1230R Integrated Amplifier At a time when many manufacturers are using microprocessor technology to bury functions below several software layers so you need to have an owners’ manual close at hand if you want to access them, T+A has delivered an amplifier where each function has its own control, properly and clearly labelled, on the front panel. This necessarily means there are quite a few knobs and buttons, but rarely has an amplifier been so easy to use. This is especially the case because the PA1230R is one of the very few amplifiers available that allows you to adjust bass and treble individually for the left and right channels. Learn More

Krell KAV-250a factory serviced (I am Krell factory sevice in CT) in 2025 Learn More

Krell MRA mono amplifiers. The best Krell ever made. Only 50 were made I read somewhere. These were $150,000/pair when new. price is for both We have the crates. They are at the Krell factory and will ship there directly to your door after being recapped. As of 1/22 because of the worldwide pandemic situation the capacitors we prefer using are on backorder. So you may purchase these but we don't have an exact delivery date These are the best Krell amplifiers ever made. Incredible size and weight 770 lbs each in the crate. serial 10199070016 Learn More

Audiophile-grade 2 channel amplifier High-performance Class AB design Discrete high-current, bipolar output transistors Learn More

Krell FPB350m single mono Learn More

Mcinttosh MC2002 200 watt channel must truck , if not local box must be ordered from Mcintosh Learn More

Mark Levinson 532h This one recently came back from factory service Learn More

Linn Klout 2 available as of 9/24 in original box Learn More

Jeff Rowland Model 7 These are later versions and were just recapped 11/24 one pair The shipping must be quoted. Each amp is approximately 130lbs boxed. Please send you postal code. Learn More

Krell KSA250 with KSA300s internal boards overhaul completed 8/23 Learn More

Cello Performance II amplifiers We will recap the amplifiers before shipping. In very good to excellent condition, one owner since new Inquire for freight options Learn More

Mark Levinson 23.5 serviced 5/25 pics will be uploaded when complete recapped Learn More

Straightwire Virtuoso H (various lengths possible) 24' pair factory will cut to your desired length) $4560 retail Learn More

Rotel RB-1091 Mono Power Amplifier Black Power output: 500 watts into 8Ω (mono) Frequency response: 10Hz to 40kHz Total harmonic distortion: 0.03% Damping factor: 400 Gain: 27.2 dB Input sensitivity: 2.2V Signal to noise ratio: 118dB Dimensions: 432 x 92 x 407mm Weight: 7.8kg Learn More

Rotel RB-1070 Power Amplifier Power output: 130 watts per channel into 8Ω (stereo), 330 watts into 4Ω (mono) Frequency response: 4Hz to 100kHz Total harmonic distortion: 0.03% Damping factor: 500 Input sensitivity: 1V Signal to noise ratio: 120dB Speaker load impedance: 4Ω (minimum) Dimensions: 430 x 121 x 350mm Weight: 11.9kg Learn More

Rotel RB-951 Power Amplifier Power output: 50 watts per channel into 8Ω (stereo), 150 watts into 8Ω (mono) Frequency response: 15Hz to 100kHz Total harmonic distortion: 0.03% Damping factor: 280 Input sensitivity: 0.775V Signal to noise ratio: 116dB Speaker load impedance: 4Ω (minimum) Dimensions: 440 x 92 x 334mm Weight: 6.8kg Learn More

Rotel RB-970BX Power Amplifier Black Power output: 60 watts per channel into 8Ω (stereo), 180 watts into 8Ω (mono) Frequency response: 15Hz to 100kHz Total harmonic distortion: 0.03% Damping factor: 280 Input sensitivity: 1V Signal to noise ratio: 116dB Speaker load impedance: 4Ω to 16Ω Dimensions: 440 x 92 x 334mm Weight: 6.8kg Learn More

SUMO ANDROMEDA II POWER AMPLIFIER excellent cosmetics Our tech went through this and readjusted dc offset, bias Sumo Andromeda II: Solid-state stereo power amplifier. Rated power output: 240Wpc into 8 ohms (23.8dBW) with less than 0.05% THD, 400Wpc into 4 ohms (23dBW) with less than 0.1% THD, from 20Hz–20kHz. Intermodulation distortion (IMD): 0.05% from 0.25W to full power. Frequency response: ±0.1dB 20Hz–20kHz, –3dB from 0.1Hz–170kHz. Input impedance: 47k ohms. Input sensitivity: 1.8V RMS for rated output. Hum and noise: 110dB below rated power. Rise time: less than 2µs. Slew rate: 115V/µs. Damping factor: greater than 500. Dimensions: 19" W by 7" H by 16.75" D Weight (shipping): 55 lbs. Learn More

Krell KMA-100 MK2 Monoblocks Class A 100W/Channel Learn More

Nakamichi Stasis PA5 Amplifier Power output: 100 watts per channel into 8Ω (stereo) Frequency response: 7Hz to 150kHz Total harmonic distortion: 0.1% Damping factor: 60 Input sensitivity: 1.4V Signal to noise ratio: 120dB Speaker load impedance: 4Ω to 16Ω Semiconductors: 20 x transistors Dimensions: 435 x 135 x 368mm Weight: 16kg Learn More

Nakamichi Stasis PA 7 Stereo Power Amplifier Power output: 200 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.1% Damping factor: 60 Input sensitivity: 2V Signal to noise ratio: 120dB Semiconductors: 16 x output transistors per channel Dimensions: 435 x 200 x 421mm Weight: 27kg Learn More

Goldmund VSR Mononoblock Power Amplifiers Silver Faceplate Great Condition Learn More

JBL Synthesis S820 Stereo Power Amplifier Power-200 Watts Per Channel Color-Black Learn More

These have the upgraded black circuit boards with high end caps from symphonic line, high quality parts internally. these are cut and paste from the web specs I found. Hope they are accurate 1 x 110 Watts RMS @ 8 Ohms (each) 2 Ohm load stable Class A/AB 1 - 600,000 Hz frequency range 120,000µF memory (each) 120 amps current delivery <0.04% THD (not audible) >800 continuous damping factor Input impedance 22K ohms DC offset <1 mV RCA inputs 400 VA Plitron transformer (each) Sanken Epitaxial Planar Transistors 2SA1216 & 2SC2922 Anti vibration dual thickness PCB Power consumption when idle ±30Watts 4 internal fuses 250V/6.3A, 5x20mm, fast blow 18"W x 16"D x 4 1/4"H weighs 32 pounds. Learn More

Mark Levinson No. 27.5 Stereo Power Amplifier fresh recap by us unused since then 2023 Power output: 100 watts per channel into 8Ω (stereo) Frequency response: 4Hz to 122kHz Total harmonic distortion: 0.3% Gain: 26.9 dB Dimensions: 483 x 185 x 360mm Weight: 43.1kg Year: 1992 Learn More

Parasound Halo A21 2 Channel Power Amplifier Continuous power output: 250 watts RMS x 2, 20 Hz - 20 kHz, 8 Ω, all channels driven 400 watts RMS x 2, 20 Hz - 20 kHz, 4 Ω, all channels driven 750 watts RMS x 1, 20 Hz - 20 kHz, 8 Ω Current capacity: 60 amperes peak per channel Power bandwidth: 5 Hz - 100 kHz, +0/-3 dB at 1 watt Total harmonic distortion: < 0.2 % at full power IM distortion: balanced 16 V rms < 0.04 % Slew rate: > 130 V/µsecond Dynamic headroom: > 1.5 dB Interchannel crosstalk: > 80 dB at 1 kHz; > 63 dB at 20 kHz Input sensitivity: 1 V for 28.28 V, THX Reference Level Input impedance: 33 k Ω unbalanced; 66 k Ω balanced S/N ratio: 112 dB, input shorted, IHF A-weighted Damping factor: > 1100 at 20 Hz Voltage: 110V - 120V Dimensions: 17-1/2" w x 7-5/8" h x 20" d, 7" h without feet Net weight: 60 lb. Learn More

Spectral DMA-180 Stereo Power Amplifier Power Output: (continuous) @ 8 ohms - 200 Watts RMS @ 4 ohms - 400 Watts RMS @ 2 ohms - 683 Watts RMS Output Current: 60 Amps peak per channel Frequency Response: ±0.1 dB, DC-150 KHz ±1 dB, DC-1 MHz ±3 dB, DC-1.8 MHz Distortion: Static: Less than 0.015% from DC to 100 KHz Typically 0.009% @ 200 WRMS/8 ohms Dynamic: 8 Tone Cluster Test 20 KHz @ 500 Hz separation; 0.01% 8 ohms; 0.015% 4 ohms Speed: Rise Time: Less than 400 nanoseconds Settling: 1.5 microseconds to -40dB Slew Rate: 600 volts/microsecond Noise: Signal to Noise: 97dB unweighted, 107dB ASA A Crosstalk: 98dB @ full power 8 ohms Input: Impedence: 100K ohms in parallel with 100 pf Sensitivity: 1.5 volts/nominal output Power Supply: Line Voltage: 100 volts, 120 volts, 240 volts (internal wiring) AC Voltage Range: ±10% Maximum Consumption: 1600 Watts Quiescent Consumption: 250 Watts Operating Temp: 0° to 50° Celsius range; 32° to 122° Farenheit Protection Features: DC Protection Servo: 0.5 volt range Current Limit Onset: 40 Amps Thermal Protect Threshold: 85° Celsius, 185° Farenheit AC Main Fuses: 2 @ 4A 3AG slo-blo, for 100 - 120 VAC, 2 @ 2A 3AG slo-blo, for 220 - 240 VAC Fuse Status: LED indicator (2) Size and Weight: Dimensions: 48cm (19")W x 17cm (6 1/4")H x 48cm (19")D Weight: 60 lbs, 27.2 KG Net Learn More

Krell KSA250 from original owner excellent cosmetics in 5/24 Learn More

Solid-state Output power: 70Wpc into 8 ohms 20Hz-20kHz (1984) 105Wpc into 8 ohms (20.2dBW) 105W into 4 ohms (17.2dBW), both continuous power, 5Hz-45kHz, with 0.09% THD (1989). Dynamic headroom: 3.2 dB (1984). Frequency response: 3Hz-70kHz ±3dB (1984). Input impedance: 24.3k ohms (1989). Sensitivity: 1.1V for full output (1984) 120mV for 1W (1989). Dimensions: 19" W by 6" H by 15" D. Weight: 25 lbs. Learn More

McInstosh MC1000 Mono Power Amplifier One amp works properly, one needs repair (we will get to it but then the price goes up) inquire for freight quote Power output: 1000 watts into 8Ω (mono) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.005% Damping factor: 200 Input sensitivity: 2.5V Signal to noise ratio: 115dB Speaker load impedance: 2Ω to 8Ω Dimensions: 264 x 438 x 511mm Weight: 47.6kg Learn More

Krell KSA80B One owner all original excellent condition We can recap for $500 additional if desired before shipping. Later balanced version Learn More

Burmester 909 Series 5 excellent cosmetics, factory crate inquire for trucking charges FEATURES • Bridgeable for mono operation by external mono-adapters. May also be ordered in internal mono configuration from the factory • Completely balanced signal path design like all Burmester components • Input stages in Burmester Class A X-amp design • DC-coupled signal path without distorting capacitors • Generously dimensioned power supply for high current output • Effortless control of any loudspeaker through a high damping factor over the full frequency range, even at highest volume levels • Stable operation into all loads • Remote on/off feature when used with Burmester power pre-amps • Processor-controlled error diagnosis Connections: • Balanced inputs (stereo/mono) • Unbalanced input using supplied adapters (stereo mode only) • 10V DC input for remote on/off switching by Burmester pre-amps • Loudspeaker output terminals (stereo/mono) Specifications • Dimensions (WxHxD) 485 mm x 515 mm x 485 mm (19 inch x 20.3 inch x 19 inch) • Weight app. 80kg (170 lbs.) • Power output Stereo: 2 x 600 W (4 Ω), 2 x 1.250 W (1 Ω) • (at appropriate AC input) Mono: >1x 1.930 W (4 Ω), >1x 3.200 W (1 Ω) • Continous peak current 65 A • Damping factor >1000 • Noise suppression >81 dB • Input sensitivity 730 mV for full gain 320 mV for 100 W into 4 Ω load • Frequency response 0-200 kHz (-3dB) • 20 selected power transistors per channel • Rise time (stereo/mono) 1,4 μs into 4/8 Ω load • 1,9 μs into 1 Ω load • Over-dimensioned power supply with 160.000 μF filtering and a 3,5 kW torodial transformer. Learn More

Power output: 60 watts per channel into 8Ω (stereo) Frequency response: 10Hz to 60kHz Total harmonic distortion: 0.1% Damping factor: 150 Input sensitivity: 1V Signal to noise ratio: 90dB Learn More

Inputs: RCA and Balanced Power output: 200 watts per channel into 8Ω (stereo); 400w/ch into 4 ohms, 800w/ch into 2 ohms and 1600w/ch into 1 ohm Learn More

SUMO The Nine + Differential Power Amplifier Sumo gives you the real thing. The nine is a pure class A power amplifier that remains class A even when driving 4 Ohm loudspeakers. The Nine's approach to class A is so unique it earned a US patent - an amazing achievement for an audio component. Sumo's exclusive class A engineering provides all the advantages and none of the disadvantages of typical class A designs. The unit features an all aluminium anodized chassis with massive extruded heat sinking and built in whisper fan for efficient heat dissipation. Military grade G-10 glass epoxy printed circuit boards throughout. Power supply incorporating 1.4KW shielded toroidal transformer and 42,000 microfarad computer grade filter capacitors, resulting in supply voltage regulation better than 3%. Learn More

AMC 2445 - 2/4 Channel Power Amplifier Power output: 90 watts per channel into 8Ω (stereo), 45 watts per channel into 8Ω (4 channels) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.03% Damping factor: 100 Input sensitivity: 0.866V Speaker load impedance: 4Ω (minimum) Dimensions: 430 x 112 x 288mm Weight: 9.5kg Year: 2001 Learn More

Power output: 250 watts per channel into 8Ω (stereo), 1000 watts into 8Ω (mono) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.1% Input sensitivity: 1.6V Signal to noise ratio: 100dB Speaker load impedance: 4Ω (minimum) Dimensions: 19 x 20.75 x 8 inches Weight: 65lbs Learn More

Goldmund Telos 300 Stereo Power Amplifier Silver Excellent Condition Original Box And Accessories Learn More

NAP 300 Power Amplifier And 300 Power Supply: Analogue Inputs: (2) XLR Input Impedance: 18k Ohms Speaker Outputs: (2) L & R, 4mm "banana" sockets Power output: Continuous, 8 Ohms: 90 Watts per channel Transient: 500VA Quiescent Consumption: 27VA Voltage Gain: +29dB Frequency response: -3dB @ 2Hz and 70kH Minimum Load Impedance: 2 Ohms Mains supply: 100-120V or 220-240V, 50/60Hz Dimensions (H x W x D): NAP 300 and the NAP 300PS - 87 x 432 x 314mm Shipping Specs for the NAP 300 Stereo Power Amplifier: Dimensions: 23” D x 19” W x 9” H Weight: 28 lb Shipping Specs for the NA PS300 Power Supply: Dimensions:23” D x 19” W x 9” H Weight: 39 lb Learn More

Power output: 100 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.005% Damping factor: 100 Input sensitivity: 1V Signal to noise ratio: 107dB Dimensions: 425 x 170 x 285mm Weight: 16kg Learn More

Plinius 8200P Stereo Power Amplifier Black Very Good Condition Learn More

Damping factor into 8 36 Signal to noise ratio ref 100W 8 A-weighted 111dB Signal to noise ratio ref 1W 8 A-weighted 91dB Input signal for clipping 1V RMS Peak current into 1 (1kHz 1mS) +/-28 amps peak (780W peak power) Burst power 2 300 Watts 2 @1% THD+N (1kHz for 20mS, repeat 500mS IHF) Audio Inputs 2 x True balanced via XLR, 47k 34k singled ended via legacy adaptor lead Audio Outputs Crosstalk 60 dB THD + N at 2/3rds full power 8 @1kHz (0.013%) Power Output 100 Watts 8 @0.1% THD+N (100W @0.1%) 190 Watts 4 @1% THD+N Frequency Response -3dB @ 1.4Hz to 100kHz Gain +29 dB Physical Weight 37.04lbs (16.8kg) Dimensions (HxWxD) 35/8x17x121/2" (9.15x43.2x31.75cm) Power Mains Supply 115V or 230V, 50/60Hz Power Consumption Passive consumption: 26W (idle) Standby consumption: <0.5W Product Type Type Power Amplifier Learn More

Mark Levinson ML20 shippiing price is double the ship quote Learn More

sold 12/23 another kav500/5 available 1/24 Krell KAV-500/5 Krell KAV-500 Multichannel Amplifier 100 Watts/Channel into 8 Ohms, 200 Watts into 4 Ohms 400 Watts/Channel bridged (2 channels) Mfr FR 20 Hz - 20 kHz ± 0.5 dB THD < 0.03% Input Impedance 100 kOhms Size: 6.25" H x 19" W x 17" D Weight: 47 pounds Learn More

Like new condition all packing and accessories sale pending 9/30/24 do not purchase Frequency response 20 Hz to 20 kHz +0, –0.08 dB <0.5 Hz to 100 kHz +0, –3 dB Signal-to-noise ratio >95 dB, wideband, unweighted, referred to full power output >115 dB, “A”-weighted Gain 26.2 dB Total harmonic distortion <0.04% at 1 kHz, at 200 W, 8 Ω <0.15% at 20 kHz, at 200 W, 8 Ω Input impedance Single-ended: 100 kΩ Balanced: 200 kΩ Input sensitivity Single-ended or balanced: 1.96 V RMS Output power 200 W RMS at 8 Ω 360 W RMS at 4 Ω Output voltage 113 V peak-to-peak 40 V RMS Output current 13.4 A peak Slew rate 40 V/μs Output impedance <0.015Ω, 20 Hz to 20 kHz Damping factor >530, 20 Hz to 20 kHz, referred to 8W Power consumption Standby: 1 W Idle: 182 W Maximum: 2100 W Heat output Standby: 3.4 BTU/hr. Idle: 623 BTU/hr. Maximum: 7182 BTU/hr. Inputs 5 single-ended via RCA connector 5 balanced via XLR connector Outputs 5 pairs binding posts Dimensions 17.1 in. W x 7.65 in. H x 21.10 in. D 434 mm W x 194 mm H x 536 mm D Weight 95 lbs., 43.2 kg (shipping) 85 lbs., 38.6 kg (unit only) Learn More

Mcintosh MC462 Like new cosmetics, works perfectly, factory box/manual/cord In 2/25 Learn More

Power output: 120 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.002% Damping factor: 130 Input sensitivity: 1.07V Signal to noise ratio: 127dB Speaker load impedance: 4Ω to 8Ω Dimensions: 435 x 165 x 425mm Weight: 14kg Year: 1984 Learn More

Lamm M2.1 mono amplifiers in 2/25 tested fine. Inquire for shipping options Price for shipping on site is for each amp. We need a second charge for shipping. Learn More

Power output: 120 watts per channel into 8Ω (stereo) Frequency response: 0Hz to 100kHz Total harmonic distortion: 0.008% Damping factor: 70 Input sensitivity: 1V Signal to noise ratio: 115dB Dimensions: 440 x 138 x 344mm Weight: 13.5kg Learn More

Power output: 200 watts per channel into 8Ω (stereo) Frequency response: 1Hz to 100kHz Total harmonic distortion: 0.002% Damping factor: 200 Input sensitivity: 1.41V Signal to noise ratio: 124dB Dimensions: 435 x 380 x 133mm Weight: 13.7kg Learn More

Power output: 200 watts per channel into 8Ω (stereo), 600 watts into 8Ω (mono) Frequency response: 10Hz to 20kHz Total harmonic distortion: 0.09% Damping factor: 800 Gain: 27 dB Input sensitivity: 1.75V Signal to noise ratio: 110dB Semiconductors: 42 x transistors, 2 x zener diodes, 13 x diodes, 2 x IC, 2 x diode bridges Dimensions: 185 x 432 x 310mm Weight: 16kg Learn More

Power output: 140 watts per channel into 8Ω (stereo) Frequency response: 5Hz to 45kHz Total harmonic distortion: 0.09% Damping factor: 100 Gain: 28 dB Input sensitivity: 1.2V Signal to noise ratio: 95dB Speaker load impedance: 4Ω (minimum) Dimensions: 17 x 15.5 x 5.75 inches Weight: 31lbs Learn More

Power output: 200 watts per channel into 8Ω (3 channels) Frequency response: 5Hz to 45kHz Total harmonic distortion: 0.09% Damping factor: 400 Gain: 28 dB Input sensitivity: 1.4V Signal to noise ratio: 95dB Speaker load impedance: 4Ω (minimum) Dimensions: 17 x 5.75 x 15.5 inches Weight: 43lbs Year: 1998 Learn More

Power output: 100 watts per channel into 8Ω (stereo), 300 watts into 8Ω (mono) Frequency response: 4Hz to 100kHz Total harmonic distortion: 0.03% Damping factor: 180 Input sensitivity: 1V Signal to noise ratio: 110dB Speaker load impedance: 8Ω (minimum) Dimensions: 430 x 109 x 315mm Weight: 9.4kg Learn More

Power output: 60 watts per channel into 8Ω (stereo) Frequency response: 10Hz to 20kHz Total harmonic distortion: 0.04% Damping factor: 180 Gain: 27 dB Input sensitivity: 0.97V Signal to noise ratio: 110dB Semiconductors: 34 x transistors, 2 x zener diodes, 14 x diodes, 2 x IC, 2 x diode bridges Dimensions: 86 x 432 x 317mm Weight: 8.9kg Downloads Learn More